Contact the laminate manufacturer and use any recommended post-curing measures. In some cases, heavy components must be balanced with special fixtures or fixtures.ĥ. In the soldering operation, printed boards, especially paper-based printed boards, must be clamped with clamps. As long as possible, this kind of wiring should be avoided.Ĥ. Sometimes most of the wires on one side of the printed board and the wires on the other side are laid vertically, so that the thermal expansion of the two sides is not equal and cause distortion. Redesign the printed board to balance the components and copper area. Analyze plating and stress, or local stress caused by heavy components or large copper foil area. Contact the laminate manufacturer to avoid unequal copper foils on both sides. Generally, the material should be placed at an angle of 60 degrees or less with the ground.ģ. Store the material flat in the loading cardboard box or lay the material diagonally flat on the shelf. Contact the laminate manufacturer to ensure that substrates with uneven structures are not used.Ģ. Straighten the material or release the stress in the oven, and perform the cutting operation according to the inclination angle and the heating temperature of the board recommended by the laminate manufacturer. In the process of PCB processing or soldering process, the hole displacement or tilt on the material is caused by improper curing of the laminate or the stress of the substrate glass cloth structure.ġ. Warpage is caused by unequal copper wall and iron wall foils, such as 1 ounce on one side and 2 ounces on the other side: the electroplating layer is not equal, or the special printed board design causes copper stress or thermal stress.Ĥ Improper fixture or fixation during soldering, and heavy components during soldering operations can also cause warpage.ĥ. When they are placed upright, they will be bowed or deformed.ģ. Warpage can also be caused by improper storage of materials, especially paper-based laminates. At the time of receipt or after sawing and cutting, the material is warped or twisted, which is usually caused by improper lamination, improper cutting or unbalanced laminate structure.Ģ.
The 45-degree tilted soldering test is particularly effective.ġ. Inspection method: use float welding test, it is possible to carry out incoming material inspection. The tilt of the hole after soldering is also a sign of warpage and distortion of the substrate. It is now a sign: no matter before, after or during PCB processing, the substrate is warped or distorted. Be sure to find out possible overheating in warehouse storage. Turnover inventory, so that inventory is usually newly produced plates. Inspect with the laminate manufacturer to obtain the aging characteristics data of the material. When heating materials, the first-in first-out principle should be observed.Ĥ. Carefully preheat the laminate, be sure to find any overheated areas, such as those under a heating lamp. Remember: every manufacturer uses a different mixture of resins and substrates, and their recommendations will vary.ģ. Contact the laminate manufacturer to find out the specific drilling speed, feed, bit and punch temperature for each grade of laminate. Refer to the manufacturing recommendations for various types of laminates. In any problem of mechanical PCB processing performance changes, only when the problem occurs at the same time as the material batch number change, can the quality of the laminate be suspected.Ģ. The production mold should not be used for the test, otherwise the wear and change of the production mold will affect the test results. Contact the laminate manufacturer to establish a test that mimics the processing performance requirements of key mechanical PCBs. The aging of materials, mainly phenolic materials, sometimes causes the plasticizer in the material to run away, making the material more brittle than usual.ġ. The preheating cycle time before punching or drilling is too long, which sometimes affects the PCB processing of the laminate.Ĥ. Poor drilling, punching or shearing technology makes the production quality poor or inconsistent.ģ. Material curing, resin content, or plasticizer changes will affect the quality of drilling, punching and shearing of the material.Ģ. Inspection method: Inspect the incoming materials, test various key mechanical PCB processing operations, and conduct routine analysis after the incoming materials are passed through the hole metallization process.ġ. Now it is a sign: the PCB processing quality of punching, cutting, and drilling is inconsistent, the coating adhesion is poor, or the coating is uneven in the metallized hole.
0 kommentar(er)
